前沿

在配置文件redis.conf中，默認的bind 接口是127.0.0.1，也就是本地回環地址。這樣的話，訪問redis服務只能通過本機的客戶端連接，而無法通過遠程連接，

這樣可以避免將redis服務暴露于危險的網絡環境中，防止一些不安全的人隨隨便便通過遠程

連接到redis服務。

如果bind選項為空的話，那會接受所有來自于可用網絡接口的連接。

今天按裝??redis6之后在使用redis的時候出現連接不成功；安全組也開放了到底是什么問題呢？？

帶著疑問我通過redis-cli連接發現

./redis-cli -h 指定ip -p 指定端口 -a 指定密碼

發現能夠正常連接，嗯應該是port沒有設置。

后來使用了jedis實現測試

    @Test
    public void testJedisSingle() throws Exception {
            //創建一個jedis對象
        Jedis jedis = new Jedis("192.168.64.129",6379);
        jedis.set("test", "hello jedis");
        String string = jedis.get("test");
        System.out.println(string);
        jedis.close();
    }

后來得知。根據redis.conf配置文件中bind的值的不同，出現不同的提示信息；但是不影響Linux系統中redis的正常使用;

當不存在bind時

 redis.clients.jedis.exceptions.JedisDataException: DENIED Redis is running in protected mode because protected mode is enabled, no bind address was specified, no authentication password is requested to clients. In this mode connections are only accepted from the loopback interface. If you want to connect from external computers to Redis you may adopt one of the following solutions: 1) Just disable protected mode sending the command 'CONFIG SET protected-mode no' from the loopback interface by connecting to Redis from the same host the server is running, however MAKE SURE Redis is not publicly accessible from internet if you do so. Use CONFIG REWRITE to make this change permanent. 2) Alternatively you can just disable the protected mode by editing the Redis configuration file, and setting the protected mode option to 'no', and then restarting the server. 3) If you started the server manually just for testing, restart it with the '--protected-mode no' option. 4) Setup a bind address or an authentication password. NOTE: You only need to do one of the above things in order for the server to start accepting connections from the outside.

當bind 本機ip地址時

代碼可以測試通過，但是Linux系統中出現問題

  [root@root redis]# ./bin/redis-cli -c
  Could not connect to Redis at 127.0.0.1:6379: Connection refused
  Could not connect to Redis at 127.0.0.1:6379: Connection refused

當bind 為默認的127.0.0.1時

代碼測試不通過

 redis.clients.jedis.exceptions.JedisConnectionException: java.net.ConnectException: Connection refused: connect

那么這個bing參數該如何配置呢？

1.在bind中配置多個IP地址,bind 192.168.64.129 127.0.0.1 空格分割

2.將bind的值配置為bind 0.0.0.0  任何ip地址都能連接

注意

我最后就是設置成0.0.0.0了，因?yàn)椴⒉皇蔷€(xiàn)上環境，圖方便所以沒有指定指定的端口。大家如果是線上環境，這里要按照自己的情況進行配置否則會有安全問題。（ps之前的個人機器經常被植入挖礦程序??）

到此這篇關于redis中bind配置的詳細步驟的文章就介紹到這了,更多相關redis bind配置內容請搜索腳本之家以前的文章或繼續瀏覽下面的相關文章希望大家以后多多支持腳本之家！